Updated July 21, 2024

Multi-Manufacturer Modern LMP (Short Can)

WNR CLUB BASED RULES

General – Multi manufacture modern day LMP cars as raced in the various endurance races around the world from 1999 to present day utilizing a plastic chassis and the Piranha 21.5k or equal FC-130 type motors in an in-line configuration only.

Class Group – Multi Manufacture (modified)

Cars

ArrowSlot- BMW V12

Avant Slot -Audi R10 TDI, Pescarolo, Lotus Elise, Peugeot 908 TDI, Porsche RS Spyder

Carrera - Audi R8, Audi R10, Audi R18e-tron, Bentley EXP Speed 8, BMW V12 LMR, Panoz LMP, Porsche RS Spyder

Fly -“racing” and “non-racing” versions of the LolaB98/10, Panoz LMP-1

Ninco - Acura LMP2 XM, Audi R18 e-tron, BMW V12

NSR - Audi R18 TDI LMP1

Scaleauto - Porsche 963 GTP, Radical SR9 LMP, Toyota One

Scalextric - Aston Martin (Lola) LMP 1, Audi R10, Cadillac Northstar LMP, ListerStorm LMP, MG Lola LMP, Peugeot 908 HDI, Porsche RS Spyder

SCX - Audi R8, Audi R10 TDI, Cadillac Northstar LMP, Dome-Judd (S101),Ferrari 333SP, Peugeot 908 HDI

Sloter – Zytek

Sloting Plus - Reynard 2KQ

Slot.it - Audi R8C, Audi R8 LMP, Audi R18 TDI, Lola Aston Martin DBR1-2, LolaB9/60, Lola B10/60, Lola B11/80, Lola B12/69 EV, Lola B12/80

Spirit - Courage, Dallara, Lola, Reynard

SRC – Porsche 919, Toyota LMP1

(Note: The above lists of cars are those that are known to have raced classified as “LMP” in some form since 1999.  There may be future modifications to the list.  Not all cars listed will allow the direct fitting of a FC-130 type motor in an in-line configuration without the use of a motor adaptor, the replacement of the chassis with a 3D printed type, the replacement of the motor pod, replacement of the body with one designed specifically for an in-line configuration (Slot.it), and/or modifications or replacement of the interior.)

Motor(s) – Piranha 21.5k,Slot.it 23k (MX16/MX16-M) “orange”/“white” end bell, NSR Shark 21.5 EVO, Thunderslot 21.5k MTMACH21/21DS, or equal (Note: must be run configured as in-line only)

Motor Downforce – maximum 25 grams

Ballast Weight – may be added

Guide – any manufacture’s guide may beused

Gears – any manufacture’s in-line gearsmay be used

Tires – front: open (may be gluedand lightly trued for roundness only/rear: open (NO F1 tires)

Wheels – any manufacture’s wheels may be used (NO F1 types)

Build rules –

Chassis – may be factory stock or upgraded with a 3D printed type;may use any manufacture’s axles, bushings, gears, tires, wheels (no F1 type),and other parts including motor pods in an in-line configuration only.  Motor adapters maybe used to fit a FC-130 type motor to locations where a boxer (FK-180) or SCXtype motor would have been normally installed.

Body – factory stock, replacement light weight interiors permitted. (Note: minimal modifications permitted to fit motors.)